如果自上料水泥攪拌車有刮花情況，需要及時進行處理，以保證攪拌車的正常使用和延長其壽命。以下是一些常見的刮花磨損現象以及處理方法：

If there are scratches on the self feeding cement mixer truck, timely treatment is necessary to ensure the normal use of the mixer truck and extend its lifespan. The following are some common scratches and wear phenomena and treatment methods:

1、攪拌車小傷痕的修補：

1. Repair of small scratches on the mixer truck:

攪拌車身如果發現傷痕，先檢查傷痕的程度。如果只是很淺的刮傷表漆，立即用混合劑處理，擦拭方法為直線擦拭。傷痕消失后，用更細的混合劑擦拭之后再打上蠟。

If any scars are found when stirring the car body, first check the extent of the scars. If it is only a shallow scratch on the surface paint, immediately treat it with a mixture and wipe it in a straight line. After the scars disappear, wipe with a finer mixture before applying wax.

2、攪拌車擦傷的修補：

2. Repair of scratches on the mixing truck:

所有的攪拌車在使用過程中都有擦傷，修補方法是傷痕部分填上與車身相同的鍍膜劑。鍍膜劑可涂一次、二次、三次，次數越多，會涂得越干凈。但整個攪拌車身的均勻處理也很重要。

All mixing trucks have scratches during use, and the repair method is to fill the damaged parts with the same coating agent as the vehicle body. The coating agent can be applied once, twice, or three times, and the more times it is applied, the cleaner it will be applied. But the uniform treatment of the entire mixing body is also important.

3、攪拌車表漆剝落的修補：

3. Repair of paint peeling on the mixer truck surface:

較深的傷痕，是觀察金屬面是否露出，如果看不到金屬面就不會生銹，可以專心地涂上修飾漆。用筆尖一點一點地點上去，然后等漆完全干。

For deeper scars, the key is to observe whether the metal surface is exposed. If the metal surface is not visible, it will not rust. You can focus on applying decorative paint. Use the tip of the pen to apply it bit by bit, and then wait for the paint to completely dry.

4、攪拌車較深傷痕的修補：

4. Repair of deep scars on the mixer truck:

很深但細長的傷痕，用彩色油灰可以修補得很好。傷痕處用砂紙，不要隨便將傷痕面擴大，重要的是將臟污清除干凈。油灰要仔細地涂抹，使之完全進入內部。涂上混合劑、上蠟，結束工作。

Deep but slender scars can be repaired well with colored putty. Use sandpaper at the scar area, do not randomly enlarge the scar surface, it is important to clean the dirt. The putty should be carefully applied so that it fully enters the interior. Apply the mixture, wax, and finish the work.

5、攪拌車凹陷的修補：

5. Repair of dents in the mixer truck:

凹陷處理是車身保養中麻煩的工作之一，重要的是打好底子，若這個步驟做不好，涂裝做得再好效果都不佳。噴漆時，不要忘記用報紙遮好四周，使涂料不要向周圍擴散。

Depression treatment is one of the troublesome tasks in vehicle maintenance, and the important thing is to lay a solid foundation. If this step is not done well, no matter how well the coating is done, the effect will not be good. When painting, do not forget to cover the surroundings with newspapers to prevent the paint from spreading around.

6、攪拌車的防銹：

6. Rust prevention of mixing trucks:

發現車體生銹后，立即著手解決，如果放任不管，銹點就會慢慢擴大。防止生銹的方法是用砂紙擦凈，或用使銹點變化的化學合成劑。

After discovering rust on the car body, immediately start solving it. If left unchecked, the rust spots will gradually expand. The method to prevent rust is to clean it with sandpaper or use a chemical synthetic agent that changes the rust spots.

7、攪拌車漏水對策：

7. Countermeasures for water leakage in the mixing truck:

車門、行李箱周圍粘貼的防水條容易剝落、扭曲。但如果沒有破裂、變形，可以再一次使用，只需將它重新粘貼，就可以防止漏水。用保護劑恢復橡膠本身的彈力也很重要。

The waterproof strips pasted around the car doors and luggage compartments are prone to peeling and twisting. But if it is not cracked or deformed, it can be used again, just by re pasting it to prevent water leakage. It is also important to restore the elasticity of the rubber itself with protective agents.

8、攪拌車機油保養竅門：

8. Tips for maintaining mixer truck oil:

機油量過多過少都會影響引擎，理想的量是緊靠油量刻度上限的部位。補充用機油，盡量準備與使用中的機油相同等級的產品。注意不要濺到引擎周圍，一個月檢測一次。

Too much or too little oil can affect the engine, and the ideal amount is close to the upper limit of the oil level scale. Replenish oil and try to prepare products of the same grade as the oil in use. Be careful not to splash around the engine, check once a month.

9、攪拌車保險杠傷痕的修補：

9. Repair of Bumper Scars on Mixing Truck:

保險扛的傷痕處理方法是將毛刺削去，坑洼部分涂上油灰使之平滑。專用油灰，準備各種顏色，選擇接近的顏色。與車身同色的保險杠，噴漆很重要。

The treatment method for the scars on the safety shoulder is to remove the burrs and apply putty to the potholes to make them smooth. Special putty, prepare various colors, and choose similar colors. Painting the bumper in the same color as the body is important.

1. 研磨法：使用砂紙或砂輪將刮花處進行研磨，直至平整。

1. Grinding method: Use sandpaper or grinding wheel to grind the scratched area until it is flat.

2. 填補法：使用填補材料將刮花處填補平整，等填補材料干透后再進行打磨。

2. Filling method: Use filling material to fill the scraped area flat, and wait for the filling material to dry thoroughly before polishing.

3. 磨灰法：如果刮花較淺，可以用灰針磨灰使刮花處的灰面勻整，再用布擦拭干凈。

3. Grinding method: If the scraping is shallow, a dust needle can be used to grind the dust surface at the scraping point to make it even, and then a cloth can be used to wipe it clean.

4. 漆面噴涂法：對于嚴重的刮花，可以將刮花處的油漆研磨掉，再進行漆面噴涂，使攪拌車表面恢復平整。需要注意的是，對于涂料顏色需要與原來的顏色相同，否則會影響攪拌車的美觀度。

4. Paint spraying method: For severe scratches, the paint at the scratches can be ground off and then sprayed to restore a smooth surface of the mixer truck. It should be noted that the paint color should be the same as the original color, otherwise it will affect the aesthetics of the mixing truck.

同時，在進行處理時尋求的維修人員進行處理，保證處理效果和安全性。更多相關事項就來我們網站http://sansungmobile.cn咨詢吧！

At the same time, seek professional maintenance personnel for handling to ensure the effectiveness and safety of the treatment. For more related matters, come to our website http://sansungmobile.cn Consult!